The model PDCPOE1224DR is a DC to DC converter with Power Over Ethernet Injector output. This product was designed and manufactured by AIR802 for use in applications where 12 vdc voltage input exists and the equipment being installed requires power-over-Ethernet (PoE) with 24 vdc. This model is designed for din rail mounting. AIR802 offers short sections of DIN Rail mount for our customers.
Two options for the input voltage exist. The default or primary use is to connect the + and - leads to the screw terminal which plugs into the front of the device. This allows direct connectivity to a battery, dc fuse terminal or other dc source. Optionally, the dc input voltage may enter from the network jack as PoE by opening the housing and sliding the slide switch to the opposite position.
There are two shielded Ethernet jacks on the top of the device. One jack is labeled, "Network" for network connectivity and will ordinarily connect to a switch, router, computer or other device. The other jack is labeled, "Equip + PoE" and is the output jack with 24vdc. Internally the data pins 1,2,3 and 6 are internally connected together between the two jacks. Pins 4 and 5 (+24vdc) and pins 7 and 8 (ground) are switched between the external dc connector or the Network jack to the Equip + PoE jack.
This model is designed for use with non-standard or pre-standard IEEE 802.3af specifications. It allows 24vdc output to flow without any detection signature. Many manufacturers' products are non-standard which allows for lower cost products. AIR802 offers another model, PDCPOEVA48AF for use with powered devices (PD) requiring IEEE 802.3af Mode B operation.
Applications of the DC - DC Converter + PoE Injector 12 VDC In and 24VDC PoE Out (Din Rail Mount):
• Powering access points requiring 24vdc in marine vessels
• Powering access points requiring 24vdc in autos, trucks and RVs
• Powering access points or other devices from 12 vdc solar systems
• Oil & Gas Industry, Automotive, Marine, WISP and other sectors
• Any scenario where 24vdc PoE is required from a 12 vdc supply
Specifications
POWER INPUT
|
|
Input DC Voltage Range
|
10 to 24 vdc
|
Efficiency
|
75 to 84% (typical)
|
Minimum Current
|
2 amps @ 10 vdc
|
Input Options
|
PoE or Direct Screw Terminal
|
POWER OUTPUT
|
|
Output DC Voltage
|
24 vdc
|
Maximum Current
|
0.8 amps (0.6 amps typical)
|
Maximum Power
|
20 watts
|
Voltage Tolerance
|
+/- 5%
|
Short Circuit Protection |
Yes |
Over Current Protection |
Yes |
Over Voltage Protection |
Yes |
ENVIRONMENTAL
|
|
Operating Temperature
|
-30℃ to 75℃ (-22º to 167ºF)
|
Humidity
|
5 to 90% RH
|
Safety Standards |
UL 60950-1 (In process), CE |
MECHANICAL |
|
Mounting |
DIN rail |
Enclosure Material |
PC UL 94 V-0 |
Dimensions - Height |
10cm (3.9 inches) |
Dimensions - Depth |
9cm (3.5 inches) *from DIN rail mount to edge of DC connector |
Dimensions - Width |
4cm (1.5 inches) |
Weight |
224 grams (7.9 ounces) |
Product Warranty
This antenna is of absolute quality and is fully covered under by the AIR802 LLC Limited Warranty.
Terminology Note: Due to various use of terminology, this product maybe referred to as: power-over-Ethernet injector, poe injector, dc-dc converter, dc-dc conversion with poe, 12 to 24 volt converter, 24 to 48 volt poe converter,Power over Ethernet (PoE) Conversion Kit, 12VDC to 24VDC PoE Kit, 12 volt to 24 volt DC/DC Boost Converter
tel: (630) 428-3108 fax: (630) 428-1575 sales@air802.com ventas@air802.com
|